How to Set Up and Use an Air Compressor?

An air compressor is one of the versatile tools to be used at home or in a garage. There are numerous power tools that run solely with compressed air. These tools may include grinders, nail guns, staplers, and sanders. It has also some important uses like inflating tires and powering sprayers for paint. Of course, before you begin to utilize a specific type of air compressor, then the tool should be properly set up to make sure that you are working a safe operation. Always remember that compressed air would be very risky or dangerous which may cause serious injuries, especially if the tool was improperly used.

For setting up the tools that you have, you have to be knowledgeable enough about the proper and right procedures to do. You may take a look at the following steps on how to set it up as your guide:

How to Set Up An Air Compressor?

Step 1: Find the compressor in a place where there is no debris or any dust

Though there is an air filter on the air compressor, it may still clog the filter if there is an excessive debris or dust that may hinder the way. This may eventually damage some internal components of your air compressor.

Step 2Connect the compressor into the outlet with appropriate voltage

It may always vary because it depends on the air compressor’s size that you’re using. For most air compressors that have 115 volts, 15-amp outlet is sufficient enough to run it. You can see the voltage and power consumption of your tool on the service plate since it was listed there.

Step 3: If necessary, fill your compressor with dedicated oil

The oil should be on the “full” line status on its site glass. Some of the air compressors may come in an oil-less; but some of them may require more oil. It would be better if you will review your manual for you to see if which type you had bought.

Step 4: Install or put a shut-off ball valve at the air compressor’s discharge port 

You may probably need a mini pipe nipple from the port to its shutoff valve if it is a female discharge port. Don’t forget to wrap it with pipe thread tape around its threads for about two layers before you screw them together. Then, tighten the shutoff valve properly using the pipe wrench or channel locks.

Step 5: Connect the air tool to your air compressor through the use of the hose

You may probably need some pipe fittings so as to make a transition between the air compressor and the hose. Before you screw the fittings or the hose together, you should wrap it with pipe thread tape around its threads for about two layers.

Step 6: Double-check the valve at the air compressor’s bottom so as to ensure if it’s tightly closed

Then, turn the drain valve in the discharge port to “Off” position. After that, you need to turn on your compressor and let it when filling up.

Step 7: Properly set its regulator to the commensurate setting of the PSI for the air tool which you are about to utilize

This would also help you to use your tools very efficiently up to its optimum results.

Step 8: Set the valve in the discharge port to “On” position; then, test your tools if these are functioning safely and efficiently

Your air compressor will start to have cycle on and off while you are utilizing the air coming from the tank.

These things and steps that were given to you would really help you in installing or setting up the machine and the air compressor that you have purchased. As much as possible, try to be guided with proper procedures so as to make sure that you are always safe when doing your works and projects. After setting up the air compressor on your hand, then it is now ready to use it according to its purpose. But of course, there are still some considerations that you need to take before using it for good. The succeeding discussions are some of the tips and tricks that you shouldn’t forget when utilizing a specific type of air compressor.

How to Use an Air Compressor?

Utilizing a specific type of air compressor is not so much difficult. It is only a matter of knowing the proper ways and strategies so as to use it accurately and properly. If you are a beginner to this tool, then it is essential to read some reviews that would help you about this concern. If you think that you are now ready to use the tool for your works or projects, then you have to make sure that you are always safe while working.

How to Use an Air CompressorFor your reference, you may follow the lists below to avoid serious injury. The following would help you to use an air compressor nicely and effectively:

  1. Attach the compressor’s hose to the tool. Also, you have to attach the accessories which you will be using on your works. These accessories may include pressure gage, blow gun, tire inflater and some other special attachments which you wish to utilize.
  2. Plug or connect the compressor to the outlet and let it pump an air into its tank. After the air compressor reached the preset pressure, then it will create an automatic shut off and is now ready to utilize.
  3. Squeeze the congestion or the trigger so as to allow the air being compressed to come out. Then, you need to hold its trigger down and let the air remain into the place where the air is relatively needed.
  4. You have to recharge the compressor through letting it sit down without using it. You will notice that your air compressor will create a noise when it is in a charging mode. As what being mentioned earlier, your air compressor will shut off automatically when it already reached the preset limit.
  5. You may repeat these procedures until you are already done utilizing the compressor. You don’t have to be fret about the number of usage of the machine since there’s no limitation or duration on how many times you will use and recharge it for a day.

It is good to be aware about these things and procedures so that you can ensure that you are using your machine properly without any difficulty. For easier setup and utilization of the item, it would be better if you will always ask the manufacturer or your product provider about its proper usage.

Always remember to secure the instructional manual along its package so that you can have a guide when already setting up and using the air compressor. If you still don’t know or understand the procedures written on the manual or guide, then force yourself to do them. You may request your friend or some experts who know about proper setting up and using the tool. Then, you may also ask some suggestions and pieces of advice from them about the tool that you are using.

Try to check out some related reviews about the product and its uses so as to fully understand the whole product and its significance.

Leave a Comment

Your email address will not be published. Required fields are marked *